; generated by PrusaSlicer 2.4.0+win64 on 2022-01-06 at 15:01:44 UTC

; 

; external perimeters extrusion width = 0.45mm
; perimeters extrusion width = 0.45mm
; infill extrusion width = 0.45mm
; solid infill extrusion width = 0.45mm
; top infill extrusion width = 0.40mm
; support material extrusion width = 0.35mm
; first layer extrusion width = 0.42mm

M73 P0 R2
M73 Q0 S2
M201 X1000 Y1000 Z200 E5000 ; sets maximum accelerations, mm/sec^2
M203 X200 Y200 Z12 E120 ; sets maximum feedrates, mm/sec
M204 P1250 R1250 T1250 ; sets acceleration (P, T) and retract acceleration (R), mm/sec^2
M205 X8.00 Y8.00 Z0.40 E4.50 ; sets the jerk limits, mm/sec
M205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec
M107
;TYPE:Custom
M862.3 P "MK3S" ; printer model check
M862.1 P0.4 ; nozzle diameter check
M115 U3.10.0 ; tell printer latest fw version
G90 ; use absolute coordinates
M83 ; extruder relative mode
M104 S215 ; set extruder temp
M140 S60 ; set bed temp
M190 S60 ; wait for bed temp
M109 S215 ; wait for extruder temp
G28 W ; home all without mesh bed level
G80 ; mesh bed leveling
G1 Z0.2 F720
G1 Y-3 F1000 ; go outside print area
G92 E0
G1 X60 E9 F1000 ; intro line
G1 X100 E12.5 F1000 ; intro line
G92 E0
M221 S95

; Don't change E values below. Excessive value can damage the printer.
M907 E430 ; set extruder motor current
G21 ; set units to millimeters
G90 ; use absolute coordinates
M83 ; use relative distances for extrusion
M900 K0.05 ; Filament gcode LA 1.5
M900 K30 ; Filament gcode LA 1.0
M107
;LAYER_CHANGE
;Z:0.2
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;0.2


M73 P2 R2
M73 Q2 S2
G1 E-.8 F2100
M73 P3 R2
M73 Q3 S2
G1 Z.4 F720
;AFTER_LAYER_CHANGE
;0.2
G1 X104.962 Y102.62 F10800
G1 Z.2 F720
M73 P4 R2
M73 Q4 S2
G1 E.8 F2100
M204 S800
;TYPE:Skirt/Brim
;WIDTH:0.42
G1 F1200
G1 X106.216 Y101.586 E.05094
G1 X107.392 Y101.191 E.0389
G1 X108.091 Y101.101 E.02212
G1 X141.909 Y101.101 E1.06031
G1 X142.608 Y101.191 E.02212
M73 P5 R2
M73 Q5 S2
G1 X143.784 Y101.586 E.0389
G1 X144.946 Y102.489 E.04612
G1 X145.488 Y104.019 E.05091
G1 X145.488 Y105.979 E.06147
M73 Q6 S2
G1 X145.038 Y107.38 E.04612
G1 X143.784 Y108.414 E.05095
G1 X142.608 Y108.809 E.0389
G1 X141.909 Y108.899 E.02212
G1 X108.091 Y108.899 E1.06031
M73 P6 R2
G1 X107.392 Y108.809 E.02212
M73 P7 R2
M73 Q7 S2
G1 X106.216 Y108.414 E.0389
G1 X105.054 Y107.511 E.04612
G1 X104.512 Y105.979 E.05097
G1 X104.512 Y104.02 E.06143
G1 X104.944 Y102.677 E.04424
M204 S1000
G1 X105.313 Y102.804 F10800
M204 S800
G1 F1200
G1 X105.333 Y102.746 E.00195
G1 X106.359 Y101.935 E.04099
G1 X107.069 Y101.666 E.02379
G1 X108.091 Y101.478 E.03261
G1 X141.909 Y101.478 E1.06031
G1 X142.513 Y101.556 E.0191
M73 P8 R2
M73 Q8 S2
G1 X143.641 Y101.935 E.03733
G1 X144.701 Y102.794 E.04278
G1 X145.112 Y104.035 E.04097
G1 X145.112 Y105.964 E.06049
G1 X144.667 Y107.254 E.04278
G1 X143.641 Y108.065 E.04101
G1 X142.931 Y108.334 E.02379
G1 X141.909 Y108.522 E.03261
M73 Q9 S2
G1 X108.091 Y108.522 E1.06031
G1 X107.069 Y108.334 E.03261
M73 P9 R2
M73 Q10 S2
G1 X106.359 Y108.065 E.02379
G1 X105.299 Y107.206 E.04278
G1 X104.888 Y105.964 E.04102
G1 X104.888 Y104.035 E.06046
M73 P10 R2
G1 X105.294 Y102.861 E.03895
M204 S1000
; printing object (black) hinge pin.STL id:0 copy 0
;WIPE_START
G1 F8640
G1 X105.333 Y102.746 E-.0282
G1 X106.359 Y101.935 E-.30188
G1 X107.069 Y101.666 E-.17522
G1 X108.091 Y101.478 E-.24015
G1 X108.154 Y101.478 E-.01456
;WIPE_END
G1 E-.04 F2100
G1 Z.6 F720
G1 X124.6 Y105.08 F10800
G1 Z.2 F720
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
G1 F1200
G1 X108.035 Y105.08 E.51938
G1 X108.037 Y104.92 E.00501
M73 Q11 S2
G1 X141.959 Y104.92 E1.06358
M73 P11 R2
G1 X141.958 Y105.08 E.00501
M73 P12 R2
M73 Q12 S2
G1 X124.66 Y105.08 E.54236
M204 S1000
G1 X125 Y105.457 F10800
M204 S800
;TYPE:External perimeter
G1 F1200
G1 X107.662 Y105.457 E.54364
G1 X107.665 Y104.543 E.02865
M73 P13 R2
M73 Q13 S2
G1 X142.337 Y104.543 E1.08712
G1 X142.334 Y105.457 E.02865
M73 P14 R2
M73 Q14 S2
G1 X125.06 Y105.457 E.5416
M204 S1000
G1 X124.794 Y105.114 F10800
; stop printing object (black) hinge pin.STL id:0 copy 0
M106 S84.15
;LAYER_CHANGE
;Z:0.4
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;0.4


;WIPE_START
M73 Q15 S2
G1 F8640
G1 X121.769 Y105.457 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z.6 F720
;AFTER_LAYER_CHANGE
;0.4
G1 X121.769 Y108.899 F10800
G1 Z.4 F720
M73 P15 R2
G1 E.8 F2100
;TYPE:Skirt/Brim
G1 F1479
G1 X108.091 Y108.899 E.42884
G1 X107.392 Y108.809 E.02212
G1 X106.216 Y108.414 E.0389
G1 X105.054 Y107.511 E.04612
G1 X104.512 Y105.979 E.05097
G1 X104.512 Y104.02 E.06143
G1 X104.962 Y102.62 E.04612
G1 X106.216 Y101.586 E.05094
G1 X107.392 Y101.191 E.0389
G1 X108.091 Y101.101 E.02212
G1 X141.909 Y101.101 E1.06031
G1 X142.608 Y101.191 E.02212
M73 P16 R2
M73 Q16 S2
G1 X143.784 Y101.586 E.0389
G1 X144.946 Y102.489 E.04612
G1 X145.488 Y104.019 E.05091
G1 X145.488 Y105.979 E.06147
G1 X145.038 Y107.38 E.04612
M73 Q17 S2
G1 X143.784 Y108.414 E.05095
G1 X142.608 Y108.809 E.0389
G1 X141.909 Y108.899 E.02212
G1 X121.829 Y108.899 E.62959
G1 X121.829 Y108.522 F10800
M73 P17 R2
G1 F1479
G1 X108.091 Y108.522 E.43072
G1 X107.069 Y108.334 E.03261
M73 Q18 S2
G1 X106.359 Y108.065 E.02379
G1 X105.299 Y107.206 E.04278
G1 X104.888 Y105.964 E.04102
G1 X104.888 Y104.035 E.06046
G1 X105.333 Y102.746 E.04278
G1 X106.359 Y101.935 E.04099
M73 P18 R2
G1 X107.069 Y101.666 E.02379
G1 X108.091 Y101.478 E.03261
G1 X141.909 Y101.478 E1.06031
G1 X142.513 Y101.556 E.0191
M73 Q19 S2
G1 X143.641 Y101.935 E.03733
G1 X144.701 Y102.794 E.04278
G1 X145.112 Y104.035 E.04097
M73 P19 R2
G1 X145.112 Y105.964 E.06049
G1 X144.667 Y107.254 E.04278
G1 X143.641 Y108.065 E.04101
G1 X142.931 Y108.334 E.02379
G1 X141.909 Y108.522 E.03261
G1 X121.889 Y108.522 E.62771
; printing object (black) hinge pin.STL id:0 copy 0
;WIPE_START
G1 F8640
G1 X118.597 Y108.522 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z.8 F720
G1 X124.6 Y105.403 F10800
M73 Q20 S2
G1 Z.4 F720
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F1479
M73 P20 R2
G1 X108.291 Y105.403 E.55203
G1 X108.283 Y104.597 E.02729
G1 X141.717 Y104.597 E1.1317
G1 X141.709 Y105.403 E.02729
M73 P21 R2
M73 Q21 S2
G1 X124.66 Y105.403 E.57708
M204 S1000
G1 X125 Y105.81 F10800
M204 S800
;TYPE:External perimeter
G1 F1479
G1 X107.893 Y105.81 E.57906
G1 X107.87 Y104.754 E.03576
M73 P22 R2
M73 Q22 S2
G1 X107.89 Y104.19 E.01911
G1 X142.11 Y104.19 E1.15833
G1 X142.13 Y104.762 E.01937
M73 P23 R2
M73 Q23 S2
G1 X142.107 Y105.81 E.0355
G1 X125.06 Y105.81 E.57703
M204 S1000
G1 X124.793 Y105.468 F10800
;WIPE_START
G1 F8640
G1 X121.769 Y105.81 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z.8 F720
G1 X141.514 Y105 F10800
G1 Z.4 F720
M73 Q24 S2
G1 E.8 F2100
;TYPE:Gap fill
;WIDTH:0.442078
G1 F1479
M73 P24 R2
G1 X108.486 Y105 E1.0962
; stop printing object (black) hinge pin.STL id:0 copy 0
M106 S170.85
;LAYER_CHANGE
;Z:0.6
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;0.6


;WIPE_START
G1 F8640
M73 Q25 S2
G1 X111.778 Y105 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z.8 F720
;AFTER_LAYER_CHANGE
;0.6
G1 X111.778 Y108.899 F10800
G1 Z.6 F720
M73 P25 R2
G1 E.8 F2100
;TYPE:Skirt/Brim
;WIDTH:0.42
G1 F1631
G1 X108.091 Y108.899 E.11558
G1 X107.392 Y108.809 E.02212
G1 X106.216 Y108.414 E.0389
G1 X105.054 Y107.511 E.04612
G1 X104.512 Y105.979 E.05097
G1 X104.512 Y104.02 E.06143
G1 X104.962 Y102.62 E.04612
G1 X106.216 Y101.586 E.05094
G1 X107.392 Y101.191 E.0389
G1 X108.091 Y101.101 E.02212
G1 X141.909 Y101.101 E1.06031
G1 X142.608 Y101.191 E.02212
M73 P26 R1
M73 Q26 S1
G1 X143.784 Y101.586 E.0389
G1 X144.946 Y102.489 E.04612
G1 X145.488 Y104.019 E.05091
G1 X145.488 Y105.979 E.06147
G1 X145.038 Y107.38 E.04612
G1 X143.784 Y108.414 E.05095
G1 X142.608 Y108.809 E.0389
G1 X141.909 Y108.899 E.02212
G1 X111.838 Y108.899 E.94285
G1 X111.838 Y108.522 F10800
M73 P27 R1
M73 Q27 S1
G1 F1631
G1 X108.091 Y108.522 E.11746
G1 X107.069 Y108.334 E.03261
G1 X106.359 Y108.065 E.02379
G1 X105.299 Y107.206 E.04278
G1 X104.888 Y105.964 E.04102
G1 X104.888 Y104.035 E.06046
G1 X105.333 Y102.746 E.04278
G1 X106.359 Y101.935 E.04099
G1 X107.069 Y101.666 E.02379
G1 X108.091 Y101.478 E.03261
G1 X141.909 Y101.478 E1.06031
G1 X142.513 Y101.556 E.0191
M73 P28 R1
M73 Q28 S1
G1 X143.641 Y101.935 E.03733
G1 X144.701 Y102.794 E.04278
G1 X145.112 Y104.035 E.04097
G1 X145.112 Y105.964 E.06049
G1 X144.667 Y107.254 E.04278
G1 X143.641 Y108.065 E.04101
G1 X142.931 Y108.334 E.02379
G1 X141.909 Y108.522 E.03261
G1 X111.898 Y108.522 E.94097
; printing object (black) hinge pin.STL id:0 copy 0
;WIPE_START
G1 F8640
M73 P29 R1
M73 Q29 S1
G1 X108.606 Y108.522 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z1 F720
G1 X124.6 Y105.513 F10800
G1 Z.6 F720
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F1631
G1 X108.698 Y105.513 E.53825
G1 X108.699 Y104.487 E.03474
M73 P30 R1
M73 Q30 S1
G1 X141.294 Y104.487 E1.1033
G1 X141.302 Y105.513 E.03474
G1 X124.66 Y105.513 E.5633
M204 S1000
M73 Q31 S1
G1 X125 Y105.92 F10800
M204 S800
;TYPE:External perimeter
M73 P31 R1
G1 F1500
G1 X108.307 Y105.92 E.56502
G1 X108.281 Y104.757 E.03938
G1 X108.308 Y104.08 E.02294
G1 X141.692 Y104.08 E1.13001
G1 X141.719 Y105.278 E.04057
M73 P32 R1
M73 Q32 S1
G1 X141.693 Y105.92 E.02175
G1 X125.06 Y105.92 E.56299
M204 S1000
G1 X124.796 Y105.576 F10800
;WIPE_START
M73 P33 R1
M73 Q33 S1
G1 F8640
G1 X121.769 Y105.92 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z1 F720
G1 X140.34 Y104.609 F10800
G1 Z.6 F720
G1 E.8 F2100
;TYPE:Solid infill
;WIDTH:0.455004
G1 F1631
G1 X140.939 Y105.208 E.02902
G1 X140.356 Y105.208 E.01997
G1 X139.941 Y104.792 E.02014
G1 X139.358 Y104.792 E.01997
G1 X139.774 Y105.208 E.02014
G1 X139.191 Y105.208 E.01997
G1 X138.775 Y104.792 E.02014
G1 X138.192 Y104.792 E.01997
G1 X138.608 Y105.208 E.02014
G1 X138.025 Y105.208 E.01997
G1 X137.61 Y104.792 E.02014
G1 X137.027 Y104.792 E.01997
G1 X137.443 Y105.208 E.02014
G1 X136.86 Y105.208 E.01997
G1 X136.444 Y104.792 E.02014
G1 X135.861 Y104.792 E.01997
G1 X136.277 Y105.208 E.02014
G1 X135.694 Y105.208 E.01997
G1 X135.278 Y104.792 E.02014
G1 X134.696 Y104.792 E.01997
G1 X135.111 Y105.208 E.02014
G1 X134.529 Y105.208 E.01997
M73 Q34 S1
G1 X134.113 Y104.792 E.02014
G1 X133.53 Y104.792 E.01997
G1 X133.946 Y105.208 E.02014
G1 X133.363 Y105.208 E.01997
G1 X132.947 Y104.792 E.02014
G1 X132.365 Y104.792 E.01997
G1 X132.78 Y105.208 E.02014
G1 X132.198 Y105.208 E.01997
M73 P34 R1
G1 X131.782 Y104.792 E.02014
G1 X131.199 Y104.792 E.01997
G1 X131.615 Y105.208 E.02014
G1 X131.032 Y105.208 E.01997
G1 X130.616 Y104.792 E.02014
G1 X130.034 Y104.792 E.01997
G1 X130.449 Y105.208 E.02014
G1 X129.866 Y105.208 E.01997
G1 X129.451 Y104.792 E.02014
G1 X128.868 Y104.792 E.01997
G1 X129.284 Y105.208 E.02014
G1 X128.701 Y105.208 E.01997
G1 X128.285 Y104.792 E.02014
G1 X127.702 Y104.792 E.01997
G1 X128.118 Y105.208 E.02014
G1 X127.535 Y105.208 E.01997
G1 X127.12 Y104.792 E.02015
G1 X126.537 Y104.792 E.01997
G1 X126.953 Y105.208 E.02015
G1 X126.37 Y105.208 E.01997
G1 X125.954 Y104.792 E.02015
G1 X125.371 Y104.792 E.01997
G1 X125.787 Y105.208 E.02014
G1 X125.204 Y105.208 E.01997
G1 X124.789 Y104.792 E.02014
G1 X124.206 Y104.792 E.01997
G1 X124.621 Y105.208 E.02015
G1 X124.039 Y105.208 E.01997
G1 X123.623 Y104.792 E.02015
G1 X123.04 Y104.792 E.01997
G1 X123.456 Y105.208 E.02014
G1 X122.873 Y105.208 E.01997
G1 X122.457 Y104.792 E.02014
G1 X121.875 Y104.792 E.01997
G1 X122.29 Y105.208 E.02014
G1 X121.708 Y105.208 E.01997
G1 X121.292 Y104.792 E.02015
G1 X120.709 Y104.792 E.01997
G1 X121.125 Y105.208 E.02015
G1 X120.542 Y105.208 E.01997
G1 X120.126 Y104.792 E.02015
M73 Q35 S1
G1 X119.544 Y104.792 E.01997
G1 X119.959 Y105.208 E.02015
G1 X119.377 Y105.208 E.01997
G1 X118.961 Y104.792 E.02015
G1 X118.378 Y104.792 E.01997
G1 X118.794 Y105.208 E.02015
G1 X118.211 Y105.208 E.01997
G1 X117.795 Y104.792 E.02015
M73 P35 R1
G1 X117.212 Y104.792 E.01997
G1 X117.628 Y105.208 E.02015
G1 X117.045 Y105.208 E.01997
G1 X116.63 Y104.792 E.02015
G1 X116.047 Y104.792 E.01997
G1 X116.463 Y105.208 E.02015
G1 X115.88 Y105.208 E.01997
G1 X115.464 Y104.792 E.02015
G1 X114.881 Y104.792 E.01997
G1 X115.297 Y105.208 E.02015
G1 X114.714 Y105.208 E.01997
G1 X114.299 Y104.792 E.02015
G1 X113.716 Y104.792 E.01997
G1 X114.132 Y105.208 E.02015
G1 X113.549 Y105.208 E.01997
G1 X113.133 Y104.792 E.02015
G1 X112.55 Y104.792 E.01997
G1 X112.966 Y105.208 E.02015
G1 X112.383 Y105.208 E.01997
G1 X111.967 Y104.792 E.02015
G1 X111.385 Y104.792 E.01997
G1 X111.8 Y105.208 E.02015
G1 X111.218 Y105.208 E.01997
G1 X110.802 Y104.792 E.02015
G1 X110.219 Y104.792 E.01997
G1 X110.635 Y105.208 E.02015
G1 X110.052 Y105.208 E.01997
G1 X109.636 Y104.792 E.02015
G1 X109.054 Y104.792 E.01997
G1 X109.653 Y105.391 E.02902
; stop printing object (black) hinge pin.STL id:0 copy 0
M106 S255
;LAYER_CHANGE
;Z:0.8
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;0.8


;WIPE_START
G1 F8640
G1 X109.054 Y104.792 E-.19557
G1 X109.636 Y104.792 E-.13456
G1 X110.052 Y105.208 E-.13575
G1 X110.635 Y105.208 E-.13456
G1 X110.219 Y104.792 E-.13575
G1 X110.322 Y104.792 E-.02379
;WIPE_END
G1 E-.04 F2100
G1 Z1 F720
;AFTER_LAYER_CHANGE
;0.8
; printing object (black) hinge pin.STL id:0 copy 0
G1 X124.6 Y105.581 F10800
G1 Z.8 F720
M73 Q36 S1
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F900
M73 P36 R1
G1 X109.126 Y105.581 E.52379
G1 X109.111 Y104.766 E.02759
G1 X109.126 Y104.419 E.01177
G1 X140.874 Y104.419 E1.07463
G1 X140.889 Y104.774 E.01202
M73 P38 R1
M73 Q38 S1
G1 X140.875 Y105.581 E.02734
G1 X124.66 Y105.581 E.54884
M204 S1000
G1 X125 Y105.988 F10800
M204 S800
;TYPE:External perimeter
G1 F900
G1 X108.736 Y105.988 E.55051
G1 X108.704 Y105.268 E.0244
M73 P39 R1
M73 Q39 S1
G1 X108.704 Y104.757 E.01729
G1 X108.736 Y104.012 E.02526
G1 X141.264 Y104.012 E1.10101
G1 X141.296 Y104.765 E.02552
M73 P40 R1
M73 Q41 S1
G1 X141.296 Y105.275 E.01726
G1 X141.264 Y105.988 E.02417
G1 X125.06 Y105.988 E.54848
M204 S1000
G1 X124.795 Y105.645 F10800
;WIPE_START
M73 P41 R1
G1 F8640
G1 X121.769 Y105.988 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z1.2 F720
G1 X139.924 Y105.459 F10800
G1 Z.8 F720
M73 Q42 S1
G1 E.8 F2100
;TYPE:Solid infill
;WIDTH:0.453421
G1 F900
M73 P42 R1
G1 X140.583 Y104.8 E.03183
G1 X140.582 Y104.724 E.00258
G1 X140.078 Y104.724 E.01717
G1 X139.527 Y105.276 E.02663
G1 X138.946 Y105.276 E.01982
G1 X139.498 Y104.724 E.02662
G1 X138.917 Y104.724 E.01982
G1 X138.366 Y105.276 E.02662
G1 X137.785 Y105.276 E.01982
G1 X138.337 Y104.724 E.02662
G1 X137.756 Y104.725 E.01982
G1 X137.205 Y105.276 E.02661
G1 X136.624 Y105.276 E.01982
G1 X137.175 Y104.725 E.02661
G1 X136.595 Y104.725 E.01982
G1 X136.044 Y105.276 E.02661
G1 X135.463 Y105.276 E.01982
G1 X136.014 Y104.725 E.02661
G1 X135.434 Y104.725 E.01982
G1 X134.882 Y105.276 E.0266
G1 X134.302 Y105.276 E.01982
G1 X134.853 Y104.725 E.0266
G1 X134.272 Y104.725 E.01982
G1 X133.721 Y105.276 E.0266
G1 X133.141 Y105.276 E.01982
G1 X133.692 Y104.725 E.02659
G1 X133.111 Y104.725 E.01982
G1 X132.56 Y105.276 E.02659
G1 X131.98 Y105.276 E.01982
G1 X132.531 Y104.725 E.02659
G1 X131.95 Y104.725 E.01982
M73 Q43 S1
G1 X131.399 Y105.276 E.02658
G1 X130.819 Y105.276 E.01982
G1 X131.369 Y104.725 E.02658
G1 X130.789 Y104.725 E.01982
G1 X130.238 Y105.276 E.02658
M73 P43 R1
G1 X129.658 Y105.276 E.01982
G1 X130.208 Y104.725 E.02657
G1 X129.628 Y104.725 E.01982
G1 X129.077 Y105.276 E.02657
G1 X128.497 Y105.276 E.01982
G1 X129.047 Y104.726 E.02657
G1 X128.466 Y104.726 E.01982
G1 X127.916 Y105.276 E.02656
G1 X127.336 Y105.276 E.01982
G1 X127.886 Y104.726 E.02656
G1 X127.305 Y104.726 E.01982
G1 X126.755 Y105.276 E.02656
G1 X126.174 Y105.276 E.01982
G1 X126.725 Y104.726 E.02656
G1 X126.144 Y104.726 E.01981
G1 X125.594 Y105.276 E.02656
G1 X125.013 Y105.276 E.01982
G1 X125.564 Y104.726 E.02656
G1 X124.983 Y104.726 E.01981
G1 X124.433 Y105.276 E.02657
G1 X123.852 Y105.276 E.01982
G1 X124.403 Y104.725 E.02657
G1 X123.822 Y104.725 E.01981
G1 X123.272 Y105.276 E.02657
G1 X122.691 Y105.276 E.01982
G1 X123.242 Y104.725 E.02657
G1 X122.661 Y104.725 E.01981
G1 X122.111 Y105.276 E.02658
G1 X121.53 Y105.276 E.01982
M73 Q44 S1
G1 X122.081 Y104.725 E.02658
G1 X121.5 Y104.725 E.01981
G1 X120.95 Y105.276 E.02658
G1 X120.369 Y105.276 E.01982
G1 X120.92 Y104.725 E.02658
M73 P44 R1
G1 X120.339 Y104.725 E.01981
G1 X119.789 Y105.276 E.02659
G1 X119.208 Y105.276 E.01982
G1 X119.759 Y104.725 E.02659
G1 X119.178 Y104.725 E.01981
G1 X118.627 Y105.276 E.02659
G1 X118.047 Y105.276 E.01982
G1 X118.598 Y104.725 E.02659
G1 X118.017 Y104.725 E.01981
G1 X117.466 Y105.276 E.0266
G1 X116.886 Y105.276 E.01982
G1 X117.437 Y104.725 E.0266
G1 X116.856 Y104.725 E.01981
G1 X116.305 Y105.276 E.0266
G1 X115.725 Y105.276 E.01982
G1 X116.276 Y104.725 E.0266
G1 X115.695 Y104.725 E.01981
G1 X115.144 Y105.276 E.0266
G1 X114.564 Y105.276 E.01982
G1 X115.115 Y104.725 E.02661
G1 X114.534 Y104.725 E.01981
G1 X113.983 Y105.276 E.02661
G1 X113.403 Y105.276 E.01982
G1 X113.954 Y104.725 E.02661
G1 X113.373 Y104.725 E.01981
G1 X112.822 Y105.276 E.02661
G1 X112.242 Y105.276 E.01982
G1 X112.793 Y104.724 E.02662
G1 X112.212 Y104.724 E.01981
M73 Q45 S1
G1 X111.661 Y105.276 E.02662
G1 X111.08 Y105.276 E.01982
G1 X111.632 Y104.724 E.02662
G1 X111.052 Y104.724 E.01981
M73 P45 R1
G1 X110.5 Y105.276 E.02662
G1 X109.919 Y105.276 E.01982
G1 X110.471 Y104.724 E.02663
G1 X109.891 Y104.724 E.01981
G1 X109.244 Y105.371 E.03122
; stop printing object (black) hinge pin.STL id:0 copy 0
;LAYER_CHANGE
;Z:1
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;1


;WIPE_START
G1 F8640
G1 X109.891 Y104.724 E-.21117
G1 X110.471 Y104.724 E-.13404
G1 X109.919 Y105.276 E-.18012
G1 X110.5 Y105.276 E-.13405
G1 X110.808 Y104.968 E-.10063
;WIPE_END
G1 E-.04 F2100
G1 Z1.2 F720
;AFTER_LAYER_CHANGE
;1
; printing object (black) hinge pin.STL id:0 copy 0
G1 X124.6 Y105.614 F10800
G1 Z1 F720
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F900
G1 X109.562 Y105.614 E.509
G1 X109.548 Y104.762 E.02884
M73 P46 R1
M73 Q46 S1
G1 X109.565 Y104.386 E.01273
G1 X140.437 Y104.386 E1.04496
G1 X140.452 Y104.773 E.01309
M73 P47 R1
M73 Q47 S1
G1 X140.435 Y105.614 E.02848
G1 X124.66 Y105.614 E.53397
M204 S1000
G1 X125 Y106.021 F10800
M204 S800
;TYPE:External perimeter
M73 P48 R1
M73 Q48 S1
G1 F900
G1 X109.173 Y106.021 E.53572
G1 X109.141 Y104.756 E.04283
M73 Q49 S1
G1 X109.177 Y103.979 E.02632
G1 X140.827 Y103.979 E1.07131
G1 X140.86 Y104.765 E.02661
M73 P50 R1
M73 Q50 S1
G1 X140.859 Y105.275 E.01726
G1 X140.824 Y106.021 E.02529
G1 X125.06 Y106.021 E.53358
M204 S1000
G1 X124.795 Y105.678 F10800
;WIPE_START
M73 P51 R1
M73 Q51 S1
G1 F8640
G1 X121.769 Y106.021 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z1.4 F720
G1 X139.495 Y104.508 F10800
G1 Z1 F720
G1 E.8 F2100
;TYPE:Solid infill
;WIDTH:0.450479
G1 F900
G1 X140.139 Y105.153 E.03089
G1 X140.136 Y105.309 E.00527
G1 X139.719 Y105.309 E.01415
G1 X139.102 Y104.691 E.02957
G1 X138.525 Y104.691 E.01953
G1 X139.142 Y105.309 E.02957
G1 X138.566 Y105.309 E.01953
G1 X137.949 Y104.691 E.02957
G1 X137.372 Y104.691 E.01953
G1 X137.989 Y105.309 E.02957
G1 X137.413 Y105.309 E.01953
G1 X136.796 Y104.691 E.02957
G1 X136.22 Y104.691 E.01953
G1 X136.837 Y105.309 E.02957
G1 X136.26 Y105.309 E.01953
G1 X135.643 Y104.691 E.02957
G1 X135.067 Y104.691 E.01953
M73 Q52 S1
G1 X135.684 Y105.309 E.02957
G1 X135.108 Y105.309 E.01953
G1 X134.491 Y104.691 E.02957
G1 X133.914 Y104.691 E.01953
M73 P52 R1
G1 X134.531 Y105.309 E.02957
G1 X133.955 Y105.309 E.01953
G1 X133.338 Y104.691 E.02957
G1 X132.761 Y104.691 E.01953
G1 X133.378 Y105.309 E.02957
G1 X132.802 Y105.309 E.01953
G1 X132.185 Y104.691 E.02957
G1 X131.609 Y104.691 E.01953
G1 X132.226 Y105.309 E.02957
G1 X131.649 Y105.309 E.01953
G1 X131.032 Y104.691 E.02957
G1 X130.456 Y104.691 E.01953
G1 X131.073 Y105.309 E.02957
G1 X130.497 Y105.309 E.01953
G1 X129.88 Y104.691 E.02957
G1 X129.303 Y104.691 E.01953
G1 X129.92 Y105.309 E.02957
G1 X129.344 Y105.309 E.01953
G1 X128.727 Y104.691 E.02957
G1 X128.15 Y104.691 E.01953
G1 X128.767 Y105.309 E.02957
G1 X128.191 Y105.309 E.01953
G1 X127.574 Y104.691 E.02957
G1 X126.998 Y104.691 E.01953
G1 X127.615 Y105.309 E.02957
G1 X127.038 Y105.309 E.01953
G1 X126.421 Y104.691 E.02957
G1 X125.845 Y104.691 E.01953
M73 Q53 S1
G1 X126.462 Y105.309 E.02957
G1 X125.886 Y105.309 E.01953
G1 X125.269 Y104.691 E.02957
G1 X124.692 Y104.691 E.01953
M73 P53 R1
G1 X125.309 Y105.309 E.02957
G1 X124.733 Y105.309 E.01953
G1 X124.116 Y104.691 E.02957
G1 X123.539 Y104.691 E.01953
G1 X124.156 Y105.309 E.02957
G1 X123.58 Y105.309 E.01953
G1 X122.963 Y104.691 E.02957
G1 X122.387 Y104.691 E.01953
G1 X123.004 Y105.309 E.02957
G1 X122.427 Y105.309 E.01953
G1 X121.81 Y104.691 E.02957
G1 X121.234 Y104.691 E.01953
G1 X121.851 Y105.309 E.02957
G1 X121.275 Y105.309 E.01953
G1 X120.658 Y104.691 E.02957
G1 X120.081 Y104.691 E.01953
G1 X120.698 Y105.309 E.02957
G1 X120.122 Y105.309 E.01953
G1 X119.505 Y104.691 E.02957
G1 X118.928 Y104.691 E.01953
G1 X119.545 Y105.309 E.02957
G1 X118.969 Y105.309 E.01953
G1 X118.352 Y104.691 E.02957
G1 X117.776 Y104.691 E.01953
G1 X118.393 Y105.309 E.02957
G1 X117.816 Y105.309 E.01953
G1 X117.199 Y104.691 E.02957
G1 X116.623 Y104.691 E.01953
M73 Q54 S1
G1 X117.24 Y105.309 E.02957
G1 X116.664 Y105.309 E.01953
G1 X116.047 Y104.691 E.02957
G1 X115.47 Y104.691 E.01953
M73 P54 R1
G1 X116.087 Y105.309 E.02957
G1 X115.511 Y105.309 E.01953
G1 X114.894 Y104.691 E.02957
G1 X114.317 Y104.691 E.01953
G1 X114.934 Y105.309 E.02957
G1 X114.358 Y105.309 E.01953
G1 X113.741 Y104.691 E.02957
G1 X113.165 Y104.691 E.01953
G1 X113.782 Y105.309 E.02957
G1 X113.205 Y105.309 E.01953
G1 X112.588 Y104.691 E.02957
G1 X112.012 Y104.691 E.01953
G1 X112.629 Y105.309 E.02957
G1 X112.053 Y105.309 E.01953
G1 X111.436 Y104.691 E.02957
G1 X110.859 Y104.691 E.01953
G1 X111.476 Y105.309 E.02957
G1 X110.9 Y105.309 E.01953
G1 X110.283 Y104.691 E.02957
G1 X109.857 Y104.691 E.01443
G1 X109.855 Y104.84 E.00502
G1 X110.507 Y105.492 E.03125
; stop printing object (black) hinge pin.STL id:0 copy 0
;LAYER_CHANGE
;Z:1.2
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;1.2


;WIPE_START
G1 F8640
G1 X109.855 Y104.84 E-.21291
G1 X109.857 Y104.691 E-.03423
G1 X110.283 Y104.691 E-.09835
G1 X110.9 Y105.309 E-.20148
G1 X111.476 Y105.309 E-.13309
G1 X111.231 Y105.064 E-.07995
;WIPE_END
G1 E-.04 F2100
G1 Z1.4 F720
;AFTER_LAYER_CHANGE
;1.2
; printing object (black) hinge pin.STL id:0 copy 0
G1 X124.6 Y105.614 F10800
G1 Z1.2 F720
M73 P55 R1
M73 Q55 S1
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F900
G1 X110.018 Y105.614 E.49359
G1 X110 Y104.767 E.02866
G1 X110.018 Y104.386 E.01291
G1 X139.982 Y104.386 E1.01422
G1 X140 Y104.775 E.01316
M73 P56 R1
M73 Q57 S1
G1 X139.982 Y105.614 E.02841
G1 X124.66 Y105.614 E.51864
M204 S1000
M73 P57 R1
G1 X125 Y106.021 F10800
M204 S800
;TYPE:External perimeter
G1 F900
G1 X109.63 Y106.021 E.52026
G1 X109.594 Y105.268 E.02552
M73 P58 R1
M73 Q58 S1
G1 X109.593 Y104.758 E.01726
G1 X109.63 Y103.979 E.02639
G1 X140.37 Y103.979 E1.04051
G1 X140.407 Y104.765 E.02664
M73 P59 R1
M73 Q59 S1
G1 X140.406 Y105.275 E.01723
G1 X140.37 Y106.021 E.02529
G1 X125.06 Y106.021 E.51823
M204 S1000
G1 X124.794 Y105.678 F10800
;WIPE_START
M73 P60 R1
M73 Q60 S1
G1 F8640
G1 X121.769 Y106.021 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z1.6 F720
G1 X139.031 Y105.492 F10800
G1 Z1.2 F720
G1 E.8 F2100
;TYPE:Solid infill
;WIDTH:0.453725
G1 F900
G1 X139.693 Y104.83 E.03197
G1 X139.69 Y104.692 E.00473
G1 X139.251 Y104.692 E.01502
G1 X138.634 Y105.309 E.0298
G1 X138.053 Y105.309 E.01984
G1 X138.67 Y104.692 E.0298
M73 Q61 S1
G1 X138.088 Y104.692 E.01985
G1 X137.472 Y105.309 E.02979
G1 X136.891 Y105.309 E.01984
G1 X137.507 Y104.692 E.02979
M73 P61 R1
G1 X136.926 Y104.692 E.01985
G1 X136.31 Y105.309 E.02979
G1 X135.729 Y105.309 E.01984
G1 X136.345 Y104.692 E.02978
G1 X135.764 Y104.692 E.01985
G1 X135.148 Y105.309 E.02978
G1 X134.567 Y105.309 E.01984
G1 X135.183 Y104.692 E.02978
G1 X134.602 Y104.692 E.01985
G1 X133.986 Y105.309 E.02978
G1 X133.405 Y105.309 E.01984
G1 X134.021 Y104.692 E.02977
G1 X133.44 Y104.692 E.01985
G1 X132.824 Y105.309 E.02977
G1 X132.243 Y105.309 E.01984
G1 X132.859 Y104.692 E.02977
G1 X132.278 Y104.692 E.01985
G1 X131.662 Y105.309 E.02976
G1 X131.081 Y105.309 E.01984
G1 X131.697 Y104.692 E.02976
G1 X131.116 Y104.693 E.01985
G1 X130.5 Y105.309 E.02976
G1 X129.919 Y105.309 E.01984
G1 X130.535 Y104.693 E.02975
G1 X129.954 Y104.693 E.01985
G1 X129.338 Y105.309 E.02975
G1 X128.757 Y105.309 E.01984
G1 X129.373 Y104.693 E.02975
M73 Q62 S1
G1 X128.792 Y104.693 E.01985
G1 X128.176 Y105.309 E.02974
G1 X127.595 Y105.309 E.01984
G1 X128.211 Y104.693 E.02974
M73 P62 R1
G1 X127.63 Y104.693 E.01985
G1 X127.014 Y105.309 E.02974
G1 X126.433 Y105.309 E.01984
G1 X127.049 Y104.693 E.02973
G1 X126.468 Y104.693 E.01985
G1 X125.852 Y105.309 E.02973
G1 X125.271 Y105.309 E.01984
G1 X125.887 Y104.693 E.02973
G1 X125.306 Y104.693 E.01984
G1 X124.69 Y105.309 E.02973
G1 X124.11 Y105.309 E.01984
G1 X124.725 Y104.693 E.02973
G1 X124.144 Y104.693 E.01984
G1 X123.529 Y105.309 E.02974
G1 X122.948 Y105.309 E.01984
G1 X123.563 Y104.693 E.02974
G1 X122.982 Y104.693 E.01984
G1 X122.367 Y105.309 E.02974
G1 X121.786 Y105.309 E.01984
G1 X122.401 Y104.693 E.02974
G1 X121.82 Y104.693 E.01984
G1 X121.205 Y105.309 E.02975
G1 X120.624 Y105.309 E.01984
G1 X121.24 Y104.693 E.02975
G1 X120.659 Y104.693 E.01984
G1 X120.043 Y105.309 E.02975
G1 X119.462 Y105.309 E.01984
G1 X120.078 Y104.693 E.02976
M73 Q63 S1
G1 X119.497 Y104.693 E.01984
G1 X118.881 Y105.309 E.02976
G1 X118.3 Y105.309 E.01984
M73 P63 R0
M73 Q63 S0
G1 X118.916 Y104.692 E.02976
G1 X118.335 Y104.692 E.01984
G1 X117.719 Y105.309 E.02976
G1 X117.138 Y105.309 E.01984
G1 X117.754 Y104.692 E.02977
G1 X117.173 Y104.692 E.01984
G1 X116.557 Y105.309 E.02977
G1 X115.976 Y105.309 E.01984
G1 X116.592 Y104.692 E.02977
G1 X116.011 Y104.692 E.01984
G1 X115.395 Y105.309 E.02978
G1 X114.814 Y105.309 E.01984
G1 X115.43 Y104.692 E.02978
G1 X114.85 Y104.692 E.01984
G1 X114.233 Y105.309 E.02978
G1 X113.652 Y105.309 E.01984
G1 X114.269 Y104.692 E.02978
G1 X113.688 Y104.692 E.01984
G1 X113.071 Y105.309 E.02979
G1 X112.49 Y105.309 E.01984
G1 X113.107 Y104.692 E.02979
G1 X112.526 Y104.692 E.01984
G1 X111.909 Y105.309 E.02979
G1 X111.328 Y105.309 E.01984
G1 X111.945 Y104.692 E.0298
G1 X111.364 Y104.692 E.01984
G1 X110.747 Y105.309 E.0298
G1 X110.317 Y105.309 E.0147
G1 X110.314 Y105.161 E.00504
M73 Q64 S0
G1 X110.966 Y104.508 E.03152
; stop printing object (black) hinge pin.STL id:0 copy 0
;LAYER_CHANGE
;Z:1.4
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;1.4


;WIPE_START
G1 F8640
G1 X110.314 Y105.161 E-.21307
G1 X110.317 Y105.309 E-.03408
G1 X110.747 Y105.309 E-.09937
G1 X111.364 Y104.692 E-.20143
M73 P64 R0
G1 X111.945 Y104.692 E-.13413
G1 X111.706 Y104.93 E-.07791
;WIPE_END
G1 E-.04 F2100
G1 Z1.6 F720
;AFTER_LAYER_CHANGE
;1.4
; printing object (black) hinge pin.STL id:0 copy 0
G1 X124.6 Y105.581 F10800
G1 Z1.4 F720
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F900
G1 X110.485 Y105.581 E.47778
G1 X110.469 Y104.767 E.02756
G1 X110.485 Y104.419 E.01181
M73 Q65 S0
G1 X139.517 Y104.419 E.98268
G1 X139.53 Y105.27 E.02881
M73 P66 R0
M73 Q66 S0
G1 X139.515 Y105.581 E.01056
G1 X124.66 Y105.581 E.50283
M204 S1000
G1 X125 Y105.988 F10800
M204 S800
;TYPE:External perimeter
G1 F900
G1 X110.097 Y105.988 E.50445
G1 X110.062 Y105.268 E.02442
M73 P67 R0
M73 Q67 S0
G1 X110.062 Y104.758 E.01726
G1 X110.097 Y104.012 E.02529
G1 X139.906 Y104.012 E1.00901
G1 X139.938 Y105.276 E.04283
M73 P68 R0
M73 Q68 S0
G1 X139.903 Y105.988 E.02413
G1 X125.06 Y105.988 E.50242
M204 S1000
G1 X124.795 Y105.645 F10800
;WIPE_START
M73 P69 R0
M73 Q69 S0
G1 F8640
G1 X121.769 Y105.988 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z1.8 F720
G1 X138.561 Y104.541 F10800
G1 Z1.4 F720
G1 E.8 F2100
;TYPE:Solid infill
;WIDTH:0.45601
G1 F900
G1 X139.224 Y105.204 E.03221
G1 X139.224 Y105.276 E.00248
G1 X138.712 Y105.276 E.0176
G1 X138.16 Y104.724 E.02682
G1 X137.576 Y104.724 E.02007
M73 Q70 S0
G1 X138.128 Y105.276 E.02682
G1 X137.544 Y105.276 E.02007
G1 X136.991 Y104.724 E.02682
M73 P70 R0
G1 X136.407 Y104.724 E.02007
G1 X136.959 Y105.276 E.02682
G1 X136.375 Y105.276 E.02007
G1 X135.823 Y104.724 E.02682
G1 X135.239 Y104.724 E.02007
G1 X135.791 Y105.276 E.02682
G1 X135.207 Y105.276 E.02007
G1 X134.655 Y104.724 E.02682
G1 X134.07 Y104.724 E.02007
G1 X134.623 Y105.276 E.02682
G1 X134.038 Y105.276 E.02007
G1 X133.486 Y104.724 E.02682
G1 X132.902 Y104.724 E.02007
G1 X133.454 Y105.276 E.02682
G1 X132.87 Y105.276 E.02007
G1 X132.318 Y104.724 E.02682
G1 X131.734 Y104.724 E.02007
G1 X132.286 Y105.276 E.02682
G1 X131.702 Y105.276 E.02007
G1 X131.149 Y104.724 E.02682
G1 X130.565 Y104.724 E.02007
G1 X131.117 Y105.276 E.02682
G1 X130.533 Y105.276 E.02007
G1 X129.981 Y104.724 E.02682
G1 X129.397 Y104.724 E.02007
G1 X129.949 Y105.276 E.02682
G1 X129.365 Y105.276 E.02007
G1 X128.813 Y104.724 E.02682
G1 X128.228 Y104.724 E.02007
G1 X128.781 Y105.276 E.02682
G1 X128.196 Y105.276 E.02007
M73 Q71 S0
G1 X127.644 Y104.724 E.02682
G1 X127.06 Y104.724 E.02007
M73 P71 R0
G1 X127.612 Y105.276 E.02682
G1 X127.028 Y105.276 E.02007
G1 X126.476 Y104.724 E.02682
G1 X125.892 Y104.724 E.02007
G1 X126.444 Y105.276 E.02682
G1 X125.86 Y105.276 E.02007
G1 X125.307 Y104.724 E.02682
G1 X124.723 Y104.724 E.02007
G1 X125.275 Y105.276 E.02682
G1 X124.691 Y105.276 E.02007
G1 X124.139 Y104.724 E.02682
G1 X123.555 Y104.724 E.02007
G1 X124.107 Y105.276 E.02682
G1 X123.523 Y105.276 E.02007
G1 X122.971 Y104.724 E.02682
G1 X122.386 Y104.724 E.02007
G1 X122.939 Y105.276 E.02682
G1 X122.354 Y105.276 E.02007
G1 X121.802 Y104.724 E.02682
G1 X121.218 Y104.724 E.02007
G1 X121.77 Y105.276 E.02682
G1 X121.186 Y105.276 E.02007
G1 X120.634 Y104.724 E.02682
G1 X120.05 Y104.724 E.02007
G1 X120.602 Y105.276 E.02682
G1 X120.018 Y105.276 E.02007
G1 X119.465 Y104.724 E.02682
G1 X118.881 Y104.724 E.02007
G1 X119.433 Y105.276 E.02682
G1 X118.849 Y105.276 E.02007
G1 X118.297 Y104.724 E.02682
G1 X117.713 Y104.724 E.02007
M73 Q72 S0
G1 X118.265 Y105.276 E.02682
G1 X117.681 Y105.276 E.02007
M73 P72 R0
G1 X117.129 Y104.724 E.02682
G1 X116.544 Y104.724 E.02007
G1 X117.097 Y105.276 E.02682
G1 X116.512 Y105.276 E.02007
G1 X115.96 Y104.724 E.02682
G1 X115.376 Y104.724 E.02007
G1 X115.928 Y105.276 E.02682
G1 X115.344 Y105.276 E.02007
G1 X114.792 Y104.724 E.02682
G1 X114.208 Y104.724 E.02007
G1 X114.76 Y105.276 E.02682
G1 X114.176 Y105.276 E.02007
G1 X113.623 Y104.724 E.02682
G1 X113.039 Y104.724 E.02007
G1 X113.591 Y105.276 E.02682
G1 X113.007 Y105.276 E.02007
G1 X112.455 Y104.724 E.02682
G1 X111.871 Y104.724 E.02007
G1 X112.423 Y105.276 E.02682
G1 X111.839 Y105.276 E.02007
G1 X111.287 Y104.724 E.02682
G1 X110.785 Y104.724 E.01723
G1 X110.783 Y104.805 E.00278
G1 X111.438 Y105.459 E.03179
; stop printing object (black) hinge pin.STL id:0 copy 0
;LAYER_CHANGE
;Z:1.6
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;1.6


;WIPE_START
G1 F8640
G1 X110.783 Y104.805 E-.2137
G1 X110.785 Y104.724 E-.01868
G1 X111.287 Y104.724 E-.11586
G1 X111.839 Y105.276 E-.1803
G1 X112.423 Y105.276 E-.13489
G1 X112.127 Y104.98 E-.09657
;WIPE_END
G1 E-.04 F2100
G1 Z1.8 F720
;AFTER_LAYER_CHANGE
;1.6
; printing object (black) hinge pin.STL id:0 copy 0
G1 X124.6 Y105.513 F10800
G1 Z1.6 F720
M73 P73 R0
M73 Q73 S0
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F900
G1 X110.967 Y105.513 E.46145
G1 X110.955 Y104.767 E.02526
G1 X110.968 Y104.487 E.0095
G1 X139.033 Y104.487 E.94997
G1 X139.033 Y105.513 E.03475
M73 P74 R0
M73 Q74 S0
G1 X124.66 Y105.513 E.4865
M204 S1000
G1 X125 Y105.92 F10800
M204 S800
;TYPE:External perimeter
M73 P75 R0
M73 Q75 S0
G1 F900
G1 X110.579 Y105.92 E.48813
G1 X110.548 Y105.268 E.02211
M73 P76 R0
M73 Q76 S0
G1 X110.548 Y104.758 E.01727
G1 X110.579 Y104.08 E.02298
G1 X139.423 Y104.08 E.97633
G1 X139.452 Y104.765 E.02321
M73 P77 R0
M73 Q77 S0
G1 X139.452 Y105.275 E.01725
G1 X139.421 Y105.92 E.02188
G1 X125.06 Y105.92 E.4861
M204 S1000
G1 X124.795 Y105.577 F10800
;WIPE_START
M73 P78 R0
M73 Q78 S0
G1 F8640
G1 X121.769 Y105.92 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z2 F720
G1 X138.075 Y105.391 F10800
G1 Z1.6 F720
G1 E.8 F2100
;TYPE:Solid infill
;WIDTH:0.456902
G1 F900
G1 X138.674 Y104.792 E.02916
G1 X138.088 Y104.792 E.02015
G1 X137.672 Y105.208 E.02025
G1 X137.087 Y105.208 E.02015
G1 X137.503 Y104.792 E.02025
G1 X136.917 Y104.792 E.02015
G1 X136.502 Y105.208 E.02025
G1 X135.916 Y105.208 E.02015
G1 X136.332 Y104.792 E.02025
G1 X135.747 Y104.792 E.02015
G1 X135.331 Y105.208 E.02025
G1 X134.745 Y105.208 E.02015
G1 X135.161 Y104.792 E.02025
G1 X134.576 Y104.792 E.02015
G1 X134.16 Y105.208 E.02025
G1 X133.574 Y105.208 E.02015
G1 X133.99 Y104.792 E.02025
G1 X133.405 Y104.792 E.02015
G1 X132.989 Y105.208 E.02025
G1 X132.403 Y105.208 E.02015
G1 X132.819 Y104.792 E.02025
M73 Q79 S0
G1 X132.234 Y104.792 E.02015
G1 X131.818 Y105.208 E.02025
M73 P79 R0
G1 X131.232 Y105.208 E.02015
G1 X131.648 Y104.792 E.02025
G1 X131.063 Y104.792 E.02015
G1 X130.647 Y105.208 E.02025
G1 X130.061 Y105.208 E.02015
G1 X130.477 Y104.792 E.02025
G1 X129.892 Y104.792 E.02015
G1 X129.476 Y105.208 E.02025
G1 X128.891 Y105.208 E.02015
G1 X129.306 Y104.792 E.02025
G1 X128.721 Y104.792 E.02015
G1 X128.305 Y105.208 E.02025
G1 X127.72 Y105.208 E.02015
G1 X128.136 Y104.792 E.02025
G1 X127.55 Y104.792 E.02015
G1 X127.134 Y105.208 E.02025
G1 X126.549 Y105.208 E.02015
G1 X126.965 Y104.792 E.02025
G1 X126.379 Y104.792 E.02015
G1 X125.963 Y105.208 E.02025
G1 X125.378 Y105.208 E.02015
G1 X125.794 Y104.792 E.02025
G1 X125.208 Y104.792 E.02015
G1 X124.792 Y105.208 E.02025
G1 X124.207 Y105.208 E.02015
G1 X124.623 Y104.792 E.02025
G1 X124.037 Y104.792 E.02015
G1 X123.621 Y105.208 E.02025
G1 X123.036 Y105.208 E.02015
G1 X123.452 Y104.792 E.02025
G1 X122.866 Y104.792 E.02015
G1 X122.451 Y105.208 E.02025
G1 X121.865 Y105.208 E.02015
G1 X122.281 Y104.792 E.02025
G1 X121.695 Y104.792 E.02015
G1 X121.28 Y105.208 E.02025
G1 X120.694 Y105.208 E.02015
M73 Q80 S0
G1 X121.11 Y104.792 E.02025
G1 X120.525 Y104.792 E.02015
M73 P80 R0
G1 X120.109 Y105.208 E.02025
G1 X119.523 Y105.208 E.02015
G1 X119.939 Y104.792 E.02025
G1 X119.354 Y104.792 E.02015
G1 X118.938 Y105.208 E.02025
G1 X118.352 Y105.208 E.02015
G1 X118.768 Y104.792 E.02025
G1 X118.183 Y104.792 E.02015
G1 X117.767 Y105.208 E.02025
G1 X117.181 Y105.208 E.02015
G1 X117.597 Y104.792 E.02025
G1 X117.012 Y104.792 E.02015
G1 X116.596 Y105.208 E.02025
G1 X116.01 Y105.208 E.02015
G1 X116.426 Y104.792 E.02025
G1 X115.841 Y104.792 E.02015
G1 X115.425 Y105.208 E.02025
G1 X114.84 Y105.208 E.02015
G1 X115.255 Y104.792 E.02025
G1 X114.67 Y104.792 E.02015
G1 X114.254 Y105.208 E.02025
G1 X113.669 Y105.208 E.02015
G1 X114.085 Y104.792 E.02025
G1 X113.499 Y104.792 E.02015
G1 X113.083 Y105.208 E.02025
G1 X112.498 Y105.208 E.02015
G1 X112.914 Y104.792 E.02025
G1 X112.328 Y104.792 E.02015
G1 X111.912 Y105.208 E.02025
G1 X111.327 Y105.208 E.02015
G1 X111.926 Y104.609 E.02916
; stop printing object (black) hinge pin.STL id:0 copy 0
;LAYER_CHANGE
;Z:1.8
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;1.8


;WIPE_START
G1 F8640
G1 X111.327 Y105.208 E-.19563
G1 X111.912 Y105.208 E-.13518
G1 X112.328 Y104.792 E-.13581
G1 X112.914 Y104.792 E-.13518
G1 X112.498 Y105.208 E-.13581
G1 X112.595 Y105.208 E-.02238
;WIPE_END
M73 Q81 S0
G1 E-.04 F2100
G1 Z2 F720
;AFTER_LAYER_CHANGE
;1.8
; printing object (black) hinge pin.STL id:0 copy 0
G1 X124.6 Y105.403 F10800
M73 P81 R0
G1 Z1.8 F720
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F900
G1 X111.474 Y105.403 E.44429
G1 X111.468 Y104.597 E.02729
G1 X138.526 Y104.597 E.91588
G1 X138.533 Y105.403 E.02729
M73 P82 R0
M73 Q82 S0
G1 X124.66 Y105.403 E.46958
M204 S1000
G1 X125 Y105.81 F10800
M204 S800
;TYPE:External perimeter
M73 P83 R0
M73 Q83 S0
G1 F900
G1 X111.076 Y105.81 E.47132
G1 X111.053 Y104.755 E.03572
M73 P84 R0
M73 Q84 S0
G1 X111.078 Y104.19 E.01915
G1 X138.925 Y104.19 E.94258
G1 X138.946 Y105.277 E.03681
M73 P85 R0
M73 Q85 S0
G1 X138.922 Y105.81 E.01806
G1 X125.06 Y105.81 E.46921
M204 S1000
G1 X124.796 Y105.466 F10800
;WIPE_START
M73 Q86 S0
G1 F8640
M73 P86 R0
G1 X121.769 Y105.81 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z2.2 F720
G1 X138.33 Y105 F10800
G1 Z1.8 F720
G1 E.8 F2100
;TYPE:Gap fill
;WIDTH:0.441958
G1 F900
G1 X111.669 Y105 E.88461
; stop printing object (black) hinge pin.STL id:0 copy 0
;LAYER_CHANGE
;Z:2
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;2


;WIPE_START
G1 F8640
M73 P87 R0
M73 Q87 S0
G1 X114.961 Y105 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z2.2 F720
;AFTER_LAYER_CHANGE
;2
; printing object (black) hinge pin.STL id:0 copy 0
G1 X124.6 Y105.235 F10800
G1 Z2 F720
G1 E.8 F2100
M204 S800
;TYPE:Perimeter
;WIDTH:0.45
G1 F900
G1 X111.998 Y105.235 E.42657
G1 X111.987 Y104.765 E.0159
M73 P88 R0
M73 Q88 S0
G1 X138.013 Y104.766 E.88095
G1 X138.003 Y105.235 E.01588
M73 P89 R0
M73 Q89 S0
G1 X124.66 Y105.235 E.45163
M204 S1000
G1 X125 Y105.642 F10800
M204 S800
;TYPE:External perimeter
G1 F900
G1 X111.6 Y105.642 E.45359
G1 X111.58 Y104.755 E.03004
M73 P90 R0
M73 Q90 S0
G1 X111.596 Y104.358 E.01343
G1 X138.404 Y104.358 E.90743
G1 X138.42 Y104.762 E.01369
M73 P91 R0
M73 Q91 S0
G1 X138.4 Y105.642 E.02978
G1 X125.06 Y105.642 E.45156
M204 S1000
G1 X124.792 Y105.3 F10800
;WIPE_START
M73 P92 R0
M73 Q92 S0
G1 F8640
G1 X121.769 Y105.642 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z2.4 F720
G1 X122.699 Y105 F10800
G1 Z2 F720
G1 E.8 F2100
;TYPE:Gap fill
;WIDTH:0.105436
G1 F900
G1 X137.804 Y105 E.07852
;WIPE_START
G1 F8640
M73 P93 R0
M73 Q93 S0
G1 X134.513 Y105 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z2.4 F720
G1 X122.699 Y105 F10800
G1 Z2 F720
G1 E.8 F2100
;WIDTH:0.105436
G1 F900
G1 X112.196 Y105 E.0546
; stop printing object (black) hinge pin.STL id:0 copy 0
;LAYER_CHANGE
;Z:2.2
;HEIGHT:0.2
;BEFORE_LAYER_CHANGE
G92 E0.0
;2.2


;WIPE_START
G1 F8640
G1 X115.487 Y105 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z2.4 F720
;AFTER_LAYER_CHANGE
;2.2
; printing object (black) hinge pin.STL id:0 copy 0
M73 Q94 S0
G1 X125 Y105.368 F10800
M73 P94 R0
G1 Z2.2 F720
G1 E.8 F2100
M204 S800
;TYPE:External perimeter
;WIDTH:0.45
G1 F900
G1 X112.142 Y105.368 E.43524
G1 X112.142 Y104.632 E.02491
G1 X137.858 Y104.632 E.87048
G1 X137.858 Y105.368 E.02491
M73 P95 R0
M73 Q95 S0
G1 X125.06 Y105.368 E.43321
M204 S1000
G1 X124.793 Y105.025 F10800
; stop printing object (black) hinge pin.STL id:0 copy 0
;WIPE_START
M73 P96 R0
M73 Q96 S0
G1 F8640;_WIPE
G1 X121.769 Y105.368 E-.76
;WIPE_END
G1 E-.04 F2100
G1 Z2.6 F720
M107
;TYPE:Custom
; Filament-specific end gcode
G4 ; wait
M221 S100 ; reset flow
M900 K0 ; reset LA
M907 E538 ; reset extruder motor current
M104 S0 ; turn off temperature
M140 S0 ; turn off heatbed
M107 ; turn off fan
G1 Z32.2 ; Move print head up
G1 X0 Y200 F3000 ; home X axis
M84 ; disable motors
M73 P100 R0
M73 Q100 S0
; filament used [mm] = 77.81
; filament used [cm3] = 0.19
; filament used [g] = 0.23
; filament cost = 0.01
; total filament used [g] = 0.23
; total filament cost = 0.01
; estimated printing time (normal mode) = 2m 40s
; estimated printing time (silent mode) = 2m 41s

; prusaslicer_config = begin
; avoid_crossing_perimeters = 0
; avoid_crossing_perimeters_max_detour = 0
; bed_custom_model = 
; bed_custom_texture = 
; bed_shape = 0x0,250x0,250x210,0x210
; bed_temperature = 60
; before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
; between_objects_gcode = 
; bottom_fill_pattern = monotonic
; bottom_solid_layers = 4
; bottom_solid_min_thickness = 0.5
; bridge_acceleration = 1000
; bridge_angle = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 0.95
; bridge_speed = 25
; brim_separation = 0.1
; brim_type = outer_only
; brim_width = 0
; clip_multipart_objects = 1
; color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
; compatible_printers_condition_cummulative = "printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4";"nozzle_diameter[0]!=0.8 and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
; complete_objects = 0
; cooling = 1
; cooling_tube_length = 5
; cooling_tube_retraction = 91.5
; default_acceleration = 1000
; default_filament_profile = "Prusament PLA"
; default_print_profile = 0.15mm QUALITY @MK3
; deretract_speed = 0
; disable_fan_first_layers = 1
; dont_support_bridges = 0
; draft_shield = disabled
; duplicate_distance = 6
; elefant_foot_compensation = 0.2
; end_filament_gcode = "; Filament-specific end gcode"
; end_gcode = G4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200 F3000 ; home X axis\nM84 ; disable motors
; ensure_vertical_shell_thickness = 1
; external_perimeter_extrusion_width = 0.45
; external_perimeter_speed = 25
; external_perimeters_first = 0
; extra_loading_move = -2
; extra_perimeters = 0
; extruder_clearance_height = 20
; extruder_clearance_radius = 45
; extruder_colour = ""
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; extrusion_width = 0.45
; fan_always_on = 1
; fan_below_layer_time = 100
; filament_colour = #FF8000
; filament_cooling_final_speed = 3.4
; filament_cooling_initial_speed = 2.2
; filament_cooling_moves = 4
; filament_cost = 30.24
; filament_density = 1.24
; filament_diameter = 1.75
; filament_load_time = 0
; filament_loading_speed = 28
; filament_loading_speed_start = 3
; filament_max_volumetric_speed = 15
; filament_minimal_purge_on_wipe_tower = 15
; filament_notes = "Affordable filament for everyday printing in premium quality manufactured in-house by Josef Prusa"
; filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
; filament_settings_id = "Prusament PLA"
; filament_soluble = 0
; filament_spool_weight = 201
; filament_toolchange_delay = 0
; filament_type = PLA
; filament_unload_time = 0
; filament_unloading_speed = 90
; filament_unloading_speed_start = 100
; filament_vendor = Prusa Polymers
; fill_angle = 45
; fill_density = 15%
; fill_pattern = gyroid
; first_layer_acceleration = 800
; first_layer_acceleration_over_raft = 0
; first_layer_bed_temperature = 60
; first_layer_extrusion_width = 0.42
; first_layer_height = 0.2
; first_layer_speed = 20
; first_layer_speed_over_raft = 30
; first_layer_temperature = 215
; full_fan_speed_layer = 4
; fuzzy_skin = none
; fuzzy_skin_point_dist = 0.8
; fuzzy_skin_thickness = 0.3
; gap_fill_enabled = 1
; gap_fill_speed = 40
; gcode_comments = 0
; gcode_flavor = marlin
; gcode_label_objects = 1
; gcode_resolution = 0.0125
; high_current_on_filament_swap = 0
; host_type = octoprint
; infill_acceleration = 1000
; infill_anchor = 2.5
; infill_anchor_max = 12
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.45
; infill_first = 0
; infill_only_where_needed = 0
; infill_overlap = 25%
; infill_speed = 80
; interface_shells = 0
; ironing = 0
; ironing_flowrate = 15%
; ironing_spacing = 0.1
; ironing_speed = 15
; ironing_type = top
; layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
; layer_height = 0.2
; machine_limits_usage = emit_to_gcode
; machine_max_acceleration_e = 5000,5000
; machine_max_acceleration_extruding = 1250,1250
; machine_max_acceleration_retracting = 1250,1250
; machine_max_acceleration_travel = 1500,1250
; machine_max_acceleration_x = 1000,960
; machine_max_acceleration_y = 1000,960
; machine_max_acceleration_z = 200,200
; machine_max_feedrate_e = 120,120
; machine_max_feedrate_x = 200,100
; machine_max_feedrate_y = 200,100
; machine_max_feedrate_z = 12,12
; machine_max_jerk_e = 4.5,4.5
; machine_max_jerk_x = 8,8
; machine_max_jerk_y = 8,8
; machine_max_jerk_z = 0.4,0.4
; machine_min_extruding_rate = 0,0
; machine_min_travel_rate = 0,0
; max_fan_speed = 100
; max_layer_height = 0.25
; max_print_height = 210
; max_print_speed = 200
; max_volumetric_speed = 0
; min_fan_speed = 100
; min_layer_height = 0.07
; min_print_speed = 15
; min_skirt_length = 4
; mmu_segmented_region_max_width = 0
; notes = 
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 0
; ooze_prevention = 0
; output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
; overhangs = 1
; parking_pos_retraction = 92
; pause_print_gcode = M601
; perimeter_acceleration = 800
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.45
; perimeter_speed = 45
; perimeters = 2
; physical_printer_settings_id = 
; post_process = 
; print_settings_id = 0.20mm QUALITY @MK3
; printer_model = MK3S
; printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
; printer_settings_id = Original Prusa i3 MK3S & MK3S+
; printer_technology = FFF
; printer_variant = 0.4
; printer_vendor = 
; raft_contact_distance = 0.2
; raft_expansion = 1.5
; raft_first_layer_density = 90%
; raft_first_layer_expansion = 3
; raft_layers = 0
; remaining_times = 1
; resolution = 0
; retract_before_travel = 1
; retract_before_wipe = 0%
; retract_layer_change = 1
; retract_length = 0.8
; retract_length_toolchange = 4
; retract_lift = 0.4
; retract_lift_above = 0
; retract_lift_below = 209
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 35
; seam_position = rear
; silent_mode = 1
; single_extruder_multi_material = 0
; single_extruder_multi_material_priming = 0
; skirt_distance = 2
; skirt_height = 3
; skirts = 1
; slice_closing_radius = 0.049
; slicing_mode = regular
; slowdown_below_layer_time = 15
; small_perimeter_speed = 25
; solid_infill_below_area = 0
; solid_infill_every_layers = 0
; solid_infill_extruder = 1
; solid_infill_extrusion_width = 0.45
; solid_infill_speed = 80
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
; start_gcode = M862.3 P "[printer_model]" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.10.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\nG92 E0\nM221 S{if layer_height<0.075}100{else}95{endif}\n\n; Don't change E values below. Excessive value can damage the printer.\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3).*/}M907 E430 ; set extruder motor current{endif}\n{if print_settings_id=~/.*(SPEED @MK3|DRAFT @MK3).*/}M907 E538 ; set extruder motor current{endif}
; support_material = 1
; support_material_angle = 0
; support_material_auto = 1
; support_material_bottom_contact_distance = 0
; support_material_bottom_interface_layers = 0
; support_material_buildplate_only = 0
; support_material_closing_radius = 2
; support_material_contact_distance = 0.2
; support_material_enforce_layers = 0
; support_material_extruder = 0
; support_material_extrusion_width = 0.35
; support_material_interface_contact_loops = 0
; support_material_interface_extruder = 0
; support_material_interface_layers = 2
; support_material_interface_pattern = rectilinear
; support_material_interface_spacing = 0.2
; support_material_interface_speed = 80%
; support_material_pattern = rectilinear
; support_material_spacing = 2
; support_material_speed = 50
; support_material_style = grid
; support_material_synchronize_layers = 0
; support_material_threshold = 50
; support_material_with_sheath = 0
; support_material_xy_spacing = 60%
; temperature = 215
; template_custom_gcode = 
; thick_bridges = 0
; thin_walls = 0
; threads = 28
; thumbnails = 
; toolchange_gcode = 
; top_fill_pattern = monotonic
; top_infill_extrusion_width = 0.4
; top_solid_infill_speed = 40
; top_solid_layers = 6
; top_solid_min_thickness = 0.7
; travel_speed = 180
; travel_speed_z = 12
; use_firmware_retraction = 0
; use_relative_e_distances = 1
; use_volumetric_e = 0
; variable_layer_height = 1
; wipe = 1
; wipe_into_infill = 0
; wipe_into_objects = 0
; wipe_tower = 1
; wipe_tower_bridging = 10
; wipe_tower_brim_width = 2
; wipe_tower_no_sparse_layers = 0
; wipe_tower_rotation_angle = 0
; wipe_tower_width = 60
; wipe_tower_x = 170
; wipe_tower_y = 125
; wiping_volumes_extruders = 70,70
; wiping_volumes_matrix = 0
; xy_size_compensation = 0
; z_offset = 0
; prusaslicer_config = end