; generated by PrusaSlicer 2.1.0+ on 2020-02-02 at 21:21:11 UTC

; 

; external perimeters extrusion width = 0.45mm
; perimeters extrusion width = 0.45mm
; infill extrusion width = 0.45mm
; solid infill extrusion width = 0.45mm
; top infill extrusion width = 0.40mm
; first layer extrusion width = 0.42mm

M73 P0 R13
M73 Q0 S13
M201 X1000 Y1000 Z1000 E5000 ; sets maximum accelerations, mm/sec^2
M203 X200 Y200 Z12 E120 ; sets maximum feedrates, mm/sec
M204 P1250 R1250 T1250 ; sets acceleration (P, T) and retract acceleration (R), mm/sec^2
M205 X8.00 Y8.00 Z0.40 E1.50 ; sets the jerk limits, mm/sec
M205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec
M107
M115 U3.8.0 ; tell printer latest fw version
G90 ; use absolute coordinates
M83 ; extruder relative mode
M104 S215 ; set extruder temp
M140 S60 ; set bed temp
M190 S60 ; wait for bed temp
M109 S215 ; wait for extruder temp
G28 W ; home all without mesh bed level
G80 ; mesh bed leveling
G1 Y-3.0 F1000.0 ; go outside print area
G92 E0.0
G1 X60.0 E9.0 F1000.0 ; intro line
M73 Q0 S13
M73 P0 R13
G1 X100.0 E12.5 F1000.0 ; intro line
G92 E0.0
M221 S95
G21 ; set units to millimeters
G90 ; use absolute coordinates
M83 ; use relative distances for extrusion
M900 K30 ; Filament gcode
;BEFORE_LAYER_CHANGE
G92 E0.0
;0.2


G1 E-0.80000 F2100.00000
G1 Z0.600 F10800.000
;AFTER_LAYER_CHANGE
;0.2
G1 X85.331 Y65.374
G1 Z0.200
G1 E0.80000 F2100.00000
M204 S1000
G1 F1200
G1 X86.037 Y64.889 E0.02687
G1 X86.880 Y64.712 E0.02698
G1 X163.104 Y64.711 E2.38995
G1 X163.930 Y64.875 E0.02642
G1 X164.634 Y65.339 E0.02642
G1 X165.110 Y66.034 E0.02642
G1 X165.288 Y66.858 E0.02642
G1 X165.288 Y143.118 E2.39110
G1 X165.125 Y143.930 E0.02597
G1 X164.669 Y144.626 E0.02608
G1 X163.953 Y145.116 E0.02721
G1 X163.102 Y145.289 E0.02721
G1 X86.882 Y145.288 E2.38984
G1 X86.070 Y145.125 E0.02597
G1 X85.374 Y144.669 E0.02608
G1 X84.884 Y143.953 E0.02721
G1 X84.711 Y143.102 E0.02721
G1 X84.712 Y66.882 E2.38984
G1 X84.875 Y66.070 E0.02597
G1 X85.298 Y65.424 E0.02420
G1 F8640
G1 X86.037 Y64.889 E-0.21076
G1 X86.880 Y64.712 E-0.19870
G1 X88.398 Y64.712 E-0.35053
G1 E-0.04000 F2100.00000
G1 Z0.800 F10800.000
G1 X87.864 Y67.864
G1 Z0.200
G1 E0.80000 F2100.00000
G1 F1200
G1 X162.136 Y67.864 E2.32874
G1 X162.136 Y142.136 E2.32874
G1 X87.864 Y142.136 E2.32874
G1 X87.864 Y67.924 E2.32686
G1 X87.487 Y67.487 F10800.000
G1 F1200
G1 X162.513 Y67.487 E2.35238
G1 X162.513 Y142.513 E2.35238
G1 X87.487 Y142.513 E2.35238
G1 X87.487 Y67.547 E2.35050
G1 X87.110 Y67.110 F10800.000
G1 F1200
G1 X162.890 Y67.110 E2.37603
G1 X162.890 Y142.890 E2.37603
G1 X87.110 Y142.890 E2.37603
M73 Q8 S12
M73 P8 R12
G1 X87.110 Y67.170 E2.37415
G1 X87.496 Y67.214 F10800.000
G1 F8640
G1 X90.401 Y67.167 E-0.76000
G1 E-0.04000 F2100.00000
G1 Z0.800 F10800.000
G1 X162.023 Y68.147
G1 Z0.200
G1 E0.80000 F2100.00000
G1 F1200
G1 X88.147 Y68.147 E2.32182
G1 X88.147 Y68.525 E0.01188
G1 X161.853 Y68.525 E2.31649
G1 X161.853 Y68.903 E0.01188
G1 X88.147 Y68.903 E2.31649
G1 X88.147 Y69.281 E0.01188
G1 X161.853 Y69.281 E2.31649
G1 X161.853 Y69.659 E0.01188
G1 X88.147 Y69.659 E2.31649
G1 X88.147 Y70.037 E0.01188
G1 X161.853 Y70.037 E2.31649
G1 X161.853 Y70.415 E0.01188
G1 X88.147 Y70.415 E2.31649
G1 X88.147 Y70.793 E0.01188
G1 X161.853 Y70.793 E2.31649
G1 X161.853 Y71.171 E0.01188
G1 X88.147 Y71.171 E2.31649
G1 X88.147 Y71.549 E0.01188
G1 X161.853 Y71.549 E2.31649
G1 X161.853 Y71.927 E0.01188
G1 X88.147 Y71.927 E2.31649
G1 X88.147 Y72.305 E0.01188
G1 X161.853 Y72.305 E2.31649
G1 X161.853 Y72.683 E0.01188
G1 X88.147 Y72.683 E2.31649
G1 X88.147 Y73.061 E0.01188
G1 X161.853 Y73.061 E2.31649
G1 X161.853 Y73.439 E0.01188
G1 X88.147 Y73.439 E2.31649
M73 Q15 S11
M73 P15 R11
G1 X88.147 Y73.817 E0.01188
G1 X161.853 Y73.817 E2.31649
G1 X161.853 Y74.195 E0.01188
G1 X88.147 Y74.195 E2.31649
G1 X88.147 Y74.573 E0.01188
G1 X161.853 Y74.573 E2.31649
G1 X161.853 Y74.951 E0.01188
G1 X88.147 Y74.951 E2.31649
G1 X88.147 Y75.329 E0.01188
G1 X161.853 Y75.329 E2.31649
G1 X161.853 Y75.707 E0.01188
G1 X88.147 Y75.707 E2.31649
G1 X88.147 Y76.085 E0.01188
G1 X161.853 Y76.085 E2.31649
G1 X161.853 Y76.463 E0.01188
G1 X88.147 Y76.463 E2.31649
G1 X88.147 Y76.841 E0.01188
G1 X161.853 Y76.841 E2.31649
G1 X161.853 Y77.219 E0.01188
G1 X88.147 Y77.219 E2.31649
G1 X88.147 Y77.597 E0.01188
G1 X161.853 Y77.597 E2.31649
G1 X161.853 Y77.975 E0.01188
G1 X88.147 Y77.975 E2.31649
G1 X88.147 Y78.353 E0.01188
G1 X161.853 Y78.353 E2.31649
G1 X161.853 Y78.731 E0.01188
G1 X88.147 Y78.731 E2.31649
G1 X88.147 Y79.109 E0.01188
G1 X161.853 Y79.109 E2.31649
G1 X161.853 Y79.487 E0.01188
G1 X88.147 Y79.487 E2.31649
G1 X88.147 Y79.865 E0.01188
G1 X161.853 Y79.865 E2.31649
M73 Q23 S10
M73 P23 R10
G1 X161.853 Y80.243 E0.01188
G1 X88.147 Y80.243 E2.31649
G1 X88.147 Y80.621 E0.01188
G1 X161.853 Y80.621 E2.31649
G1 X161.853 Y80.999 E0.01188
G1 X88.147 Y80.999 E2.31649
G1 X88.147 Y81.377 E0.01188
G1 X161.853 Y81.377 E2.31649
G1 X161.853 Y81.755 E0.01188
G1 X88.147 Y81.755 E2.31649
G1 X88.147 Y82.133 E0.01188
G1 X161.853 Y82.133 E2.31649
G1 X161.853 Y82.510 E0.01188
G1 X88.147 Y82.510 E2.31649
G1 X88.147 Y82.888 E0.01188
G1 X161.853 Y82.888 E2.31649
G1 X161.853 Y83.266 E0.01188
G1 X88.147 Y83.266 E2.31649
G1 X88.147 Y83.644 E0.01188
G1 X161.853 Y83.644 E2.31649
G1 X161.853 Y84.022 E0.01188
G1 X88.147 Y84.022 E2.31649
G1 X88.147 Y84.400 E0.01188
G1 X161.853 Y84.400 E2.31649
G1 X161.853 Y84.778 E0.01188
G1 X88.147 Y84.778 E2.31649
G1 X88.147 Y85.156 E0.01188
G1 X161.853 Y85.156 E2.31649
G1 X161.853 Y85.534 E0.01188
G1 X88.147 Y85.534 E2.31649
G1 X88.147 Y85.912 E0.01188
G1 X161.853 Y85.912 E2.31649
G1 X161.853 Y86.290 E0.01188
G1 X88.147 Y86.290 E2.31649
M73 Q31 S9
M73 P31 R9
G1 X88.147 Y86.668 E0.01188
G1 X161.853 Y86.668 E2.31649
G1 X161.853 Y87.046 E0.01188
G1 X88.147 Y87.046 E2.31649
G1 X88.147 Y87.424 E0.01188
G1 X161.853 Y87.424 E2.31649
G1 X161.853 Y87.802 E0.01188
G1 X88.147 Y87.802 E2.31649
G1 X88.147 Y88.180 E0.01188
G1 X161.853 Y88.180 E2.31649
G1 X161.853 Y88.558 E0.01188
G1 X88.147 Y88.558 E2.31649
G1 X88.147 Y88.936 E0.01188
G1 X161.853 Y88.936 E2.31649
G1 X161.853 Y89.314 E0.01188
G1 X88.147 Y89.314 E2.31649
G1 X88.147 Y89.692 E0.01188
G1 X161.853 Y89.692 E2.31649
G1 X161.853 Y90.070 E0.01188
G1 X88.147 Y90.070 E2.31649
G1 X88.147 Y90.448 E0.01188
G1 X161.853 Y90.448 E2.31649
G1 X161.853 Y90.826 E0.01188
G1 X88.147 Y90.826 E2.31649
G1 X88.147 Y91.204 E0.01188
G1 X161.853 Y91.204 E2.31649
G1 X161.853 Y91.582 E0.01188
G1 X88.147 Y91.582 E2.31649
G1 X88.147 Y91.960 E0.01188
G1 X161.853 Y91.960 E2.31649
G1 X161.853 Y92.338 E0.01188
G1 X88.147 Y92.338 E2.31649
G1 X88.147 Y92.716 E0.01188
G1 X161.853 Y92.716 E2.31649
M73 Q39 S8
M73 P39 R8
G1 X161.853 Y93.094 E0.01188
G1 X88.147 Y93.094 E2.31649
G1 X88.147 Y93.472 E0.01188
G1 X161.853 Y93.472 E2.31649
G1 X161.853 Y93.850 E0.01188
G1 X88.147 Y93.850 E2.31649
G1 X88.147 Y94.228 E0.01188
G1 X161.853 Y94.228 E2.31649
G1 X161.853 Y94.606 E0.01188
G1 X88.147 Y94.606 E2.31649
G1 X88.147 Y94.984 E0.01188
G1 X161.853 Y94.984 E2.31649
G1 X161.853 Y95.362 E0.01188
G1 X88.147 Y95.362 E2.31649
G1 X88.147 Y95.740 E0.01188
G1 X161.853 Y95.740 E2.31649
G1 X161.853 Y96.118 E0.01188
G1 X88.147 Y96.118 E2.31649
G1 X88.147 Y96.496 E0.01188
G1 X161.853 Y96.496 E2.31649
G1 X161.853 Y96.874 E0.01188
G1 X88.147 Y96.874 E2.31649
G1 X88.147 Y97.252 E0.01188
G1 X161.853 Y97.252 E2.31649
G1 X161.853 Y97.629 E0.01188
G1 X88.147 Y97.629 E2.31649
G1 X88.147 Y98.007 E0.01188
G1 X161.853 Y98.007 E2.31649
G1 X161.853 Y98.385 E0.01188
G1 X88.147 Y98.385 E2.31649
G1 X88.147 Y98.763 E0.01188
G1 X161.853 Y98.763 E2.31649
G1 X161.853 Y99.141 E0.01188
G1 X88.147 Y99.141 E2.31649
M73 Q47 S7
M73 P46 R7
G1 X88.147 Y99.519 E0.01188
G1 X161.853 Y99.519 E2.31649
G1 X161.853 Y99.897 E0.01188
G1 X88.147 Y99.897 E2.31649
G1 X88.147 Y100.275 E0.01188
G1 X161.853 Y100.275 E2.31649
G1 X161.853 Y100.653 E0.01188
G1 X88.147 Y100.653 E2.31649
G1 X88.147 Y101.031 E0.01188
G1 X161.853 Y101.031 E2.31649
G1 X161.853 Y101.409 E0.01188
G1 X88.147 Y101.409 E2.31649
G1 X88.147 Y101.787 E0.01188
G1 X161.853 Y101.787 E2.31649
G1 X161.853 Y102.165 E0.01188
G1 X88.147 Y102.165 E2.31649
G1 X88.147 Y102.543 E0.01188
G1 X161.853 Y102.543 E2.31649
G1 X161.853 Y102.921 E0.01188
G1 X88.147 Y102.921 E2.31649
G1 X88.147 Y103.299 E0.01188
G1 X161.853 Y103.299 E2.31649
G1 X161.853 Y103.677 E0.01188
G1 X88.147 Y103.677 E2.31649
G1 X88.147 Y104.055 E0.01188
G1 X161.853 Y104.055 E2.31649
G1 X161.853 Y104.433 E0.01188
G1 X88.147 Y104.433 E2.31649
G1 X88.147 Y104.811 E0.01188
G1 X161.853 Y104.811 E2.31649
G1 X161.853 Y105.189 E0.01188
G1 X88.147 Y105.189 E2.31649
G1 X88.147 Y105.567 E0.01188
G1 X161.853 Y105.567 E2.31649
M73 Q54 S6
M73 P54 R6
G1 X161.853 Y105.945 E0.01188
G1 X88.147 Y105.945 E2.31649
G1 X88.147 Y106.323 E0.01188
G1 X161.853 Y106.323 E2.31649
G1 X161.853 Y106.701 E0.01188
G1 X88.147 Y106.701 E2.31649
G1 X88.147 Y107.079 E0.01188
G1 X161.853 Y107.079 E2.31649
G1 X161.853 Y107.457 E0.01188
G1 X88.147 Y107.457 E2.31649
G1 X88.147 Y107.835 E0.01188
G1 X161.853 Y107.835 E2.31649
G1 X161.853 Y108.213 E0.01188
G1 X88.147 Y108.213 E2.31649
G1 X88.147 Y108.591 E0.01188
G1 X161.853 Y108.591 E2.31649
G1 X161.853 Y108.969 E0.01188
G1 X88.147 Y108.969 E2.31649
G1 X88.147 Y109.347 E0.01188
G1 X161.853 Y109.347 E2.31649
G1 X161.853 Y109.725 E0.01188
G1 X88.147 Y109.725 E2.31649
G1 X88.147 Y110.103 E0.01188
G1 X161.853 Y110.103 E2.31649
G1 X161.853 Y110.481 E0.01188
G1 X88.147 Y110.481 E2.31649
G1 X88.147 Y110.859 E0.01188
G1 X161.853 Y110.859 E2.31649
G1 X161.853 Y111.237 E0.01188
G1 X88.147 Y111.237 E2.31649
G1 X88.147 Y111.615 E0.01188
G1 X161.853 Y111.615 E2.31649
G1 X161.853 Y111.993 E0.01188
G1 X88.147 Y111.993 E2.31649
M73 Q62 S5
M73 P62 R5
G1 X88.147 Y112.371 E0.01188
G1 X161.853 Y112.371 E2.31649
G1 X161.853 Y112.748 E0.01188
G1 X88.147 Y112.748 E2.31649
G1 X88.147 Y113.126 E0.01188
G1 X161.853 Y113.126 E2.31649
G1 X161.853 Y113.504 E0.01188
G1 X88.147 Y113.504 E2.31649
G1 X88.147 Y113.882 E0.01188
G1 X161.853 Y113.882 E2.31649
G1 X161.853 Y114.260 E0.01188
G1 X88.147 Y114.260 E2.31649
G1 X88.147 Y114.638 E0.01188
G1 X161.853 Y114.638 E2.31649
G1 X161.853 Y115.016 E0.01188
G1 X88.147 Y115.016 E2.31649
G1 X88.147 Y115.394 E0.01188
G1 X161.853 Y115.394 E2.31649
G1 X161.853 Y115.772 E0.01188
G1 X88.147 Y115.772 E2.31649
G1 X88.147 Y116.150 E0.01188
G1 X161.853 Y116.150 E2.31649
G1 X161.853 Y116.528 E0.01188
G1 X88.147 Y116.528 E2.31649
G1 X88.147 Y116.906 E0.01188
G1 X161.853 Y116.906 E2.31649
G1 X161.853 Y117.284 E0.01188
G1 X88.147 Y117.284 E2.31649
G1 X88.147 Y117.662 E0.01188
G1 X161.853 Y117.662 E2.31649
G1 X161.853 Y118.040 E0.01188
G1 X88.147 Y118.040 E2.31649
G1 X88.147 Y118.418 E0.01188
G1 X161.853 Y118.418 E2.31649
M73 Q70 S4
M73 P70 R4
G1 X161.853 Y118.796 E0.01188
G1 X88.147 Y118.796 E2.31649
G1 X88.147 Y119.174 E0.01188
G1 X161.853 Y119.174 E2.31649
G1 X161.853 Y119.552 E0.01188
G1 X88.147 Y119.552 E2.31649
G1 X88.147 Y119.930 E0.01188
G1 X161.853 Y119.930 E2.31649
G1 X161.853 Y120.308 E0.01188
G1 X88.147 Y120.308 E2.31649
G1 X88.147 Y120.686 E0.01188
G1 X161.853 Y120.686 E2.31649
G1 X161.853 Y121.064 E0.01188
G1 X88.147 Y121.064 E2.31649
G1 X88.147 Y121.442 E0.01188
G1 X161.853 Y121.442 E2.31649
G1 X161.853 Y121.820 E0.01188
G1 X88.147 Y121.820 E2.31649
G1 X88.147 Y122.198 E0.01188
G1 X161.853 Y122.198 E2.31649
G1 X161.853 Y122.576 E0.01188
G1 X88.147 Y122.576 E2.31649
G1 X88.147 Y122.954 E0.01188
G1 X161.853 Y122.954 E2.31649
G1 X161.853 Y123.332 E0.01188
G1 X88.147 Y123.332 E2.31649
G1 X88.147 Y123.710 E0.01188
G1 X161.853 Y123.710 E2.31649
G1 X161.853 Y124.088 E0.01188
G1 X88.147 Y124.088 E2.31649
G1 X88.147 Y124.466 E0.01188
G1 X161.853 Y124.466 E2.31649
G1 X161.853 Y124.844 E0.01188
G1 X88.147 Y124.844 E2.31649
M73 Q78 S3
M73 P78 R3
G1 X88.147 Y125.222 E0.01188
G1 X161.853 Y125.222 E2.31649
G1 X161.853 Y125.600 E0.01188
G1 X88.147 Y125.600 E2.31649
G1 X88.147 Y125.978 E0.01188
G1 X161.853 Y125.978 E2.31649
G1 X161.853 Y126.356 E0.01188
G1 X88.147 Y126.356 E2.31649
G1 X88.147 Y126.734 E0.01188
G1 X161.853 Y126.734 E2.31649
G1 X161.853 Y127.112 E0.01188
G1 X88.147 Y127.112 E2.31649
G1 X88.147 Y127.490 E0.01188
G1 X161.853 Y127.490 E2.31649
G1 X161.853 Y127.867 E0.01188
G1 X88.147 Y127.867 E2.31649
G1 X88.147 Y128.245 E0.01188
G1 X161.853 Y128.245 E2.31649
G1 X161.853 Y128.623 E0.01188
G1 X88.147 Y128.623 E2.31649
G1 X88.147 Y129.001 E0.01188
G1 X161.853 Y129.001 E2.31649
G1 X161.853 Y129.379 E0.01188
G1 X88.147 Y129.379 E2.31649
G1 X88.147 Y129.757 E0.01188
G1 X161.853 Y129.757 E2.31649
G1 X161.853 Y130.135 E0.01188
G1 X88.147 Y130.135 E2.31649
G1 X88.147 Y130.513 E0.01188
G1 X161.853 Y130.513 E2.31649
G1 X161.853 Y130.891 E0.01188
G1 X88.147 Y130.891 E2.31649
G1 X88.147 Y131.269 E0.01188
G1 X161.853 Y131.269 E2.31649
M73 Q86 S2
M73 P86 R2
G1 X161.853 Y131.647 E0.01188
G1 X88.147 Y131.647 E2.31649
G1 X88.147 Y132.025 E0.01188
G1 X161.853 Y132.025 E2.31649
G1 X161.853 Y132.403 E0.01188
G1 X88.147 Y132.403 E2.31649
G1 X88.147 Y132.781 E0.01188
G1 X161.853 Y132.781 E2.31649
G1 X161.853 Y133.159 E0.01188
G1 X88.147 Y133.159 E2.31649
G1 X88.147 Y133.537 E0.01188
G1 X161.853 Y133.537 E2.31649
G1 X161.853 Y133.915 E0.01188
G1 X88.147 Y133.915 E2.31649
G1 X88.147 Y134.293 E0.01188
G1 X161.853 Y134.293 E2.31649
G1 X161.853 Y134.671 E0.01188
G1 X88.147 Y134.671 E2.31649
G1 X88.147 Y135.049 E0.01188
G1 X161.853 Y135.049 E2.31649
G1 X161.853 Y135.427 E0.01188
G1 X88.147 Y135.427 E2.31649
G1 X88.147 Y135.805 E0.01188
G1 X161.853 Y135.805 E2.31649
G1 X161.853 Y136.183 E0.01188
G1 X88.147 Y136.183 E2.31649
G1 X88.147 Y136.561 E0.01188
G1 X161.853 Y136.561 E2.31649
G1 X161.853 Y136.939 E0.01188
G1 X88.147 Y136.939 E2.31649
G1 X88.147 Y137.317 E0.01188
G1 X161.853 Y137.317 E2.31649
G1 X161.853 Y137.695 E0.01188
G1 X88.147 Y137.695 E2.31649
M73 Q94 S1
M73 P94 R1
G1 X88.147 Y138.073 E0.01188
G1 X161.853 Y138.073 E2.31649
G1 X161.853 Y138.451 E0.01188
G1 X88.147 Y138.451 E2.31649
G1 X88.147 Y138.829 E0.01188
G1 X161.853 Y138.829 E2.31649
G1 X161.853 Y139.207 E0.01188
G1 X88.147 Y139.207 E2.31649
G1 X88.147 Y139.585 E0.01188
G1 X161.853 Y139.585 E2.31649
G1 X161.853 Y139.963 E0.01188
G1 X88.147 Y139.963 E2.31649
G1 X88.147 Y140.341 E0.01188
G1 X161.853 Y140.341 E2.31649
G1 X161.853 Y140.719 E0.01188
G1 X88.147 Y140.719 E2.31649
G1 X88.147 Y141.097 E0.01188
G1 X161.853 Y141.097 E2.31649
G1 X161.853 Y141.475 E0.01188
G1 X88.147 Y141.475 E2.31649
G1 X88.147 Y141.853 E0.01188
G1 X162.023 Y141.853 E2.32182
G1 F8640;_WIPE
G1 X158.731 Y141.853 E-0.76000
G1 E-0.04000 F2100.00000
G1 Z0.800 F10800.000
; Filament-specific end gcode
G4 ; wait
M221 S100
M104 S0 ; turn off temperature
M140 S0 ; turn off heatbed
M107 ; turn off fan
G1 Z30.8 ; Move print head up
G1 X0 Y200 F3000 ; home X axis
M84 ; disable motors
M73 P100 R0
M73 Q100 S0
; filament used [mm] = 494.6
; filament used [cm3] = 1.2
; filament used [g] = 1.5
; filament cost = 0.0
; total filament used [g] = 1.5
; total filament cost = 0.0
; estimated printing time (normal mode) = 13m 24s
; estimated printing time (silent mode) = 13m 24s

; avoid_crossing_perimeters = 0
; bed_custom_model = 
; bed_custom_texture = 
; bed_shape = 0x0,250x0,250x210,0x210
; bed_temperature = 60
; before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
; between_objects_gcode = 
; bottom_fill_pattern = rectilinear
; bottom_solid_layers = 3
; bridge_acceleration = 1000
; bridge_angle = 0
; bridge_fan_speed = 100
; bridge_flow_ratio = 0.95
; bridge_speed = 20
; brim_width = 0
; clip_multipart_objects = 1
; compatible_printers_condition_cummulative = "printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4";"! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
; complete_objects = 0
; cooling = 1
; cooling_tube_length = 5
; cooling_tube_retraction = 91.5
; default_acceleration = 1000
; default_filament_profile = "Prusament PLA"
; default_print_profile = 0.15mm QUALITY MK3
; deretract_speed = 0
; disable_fan_first_layers = 1
; dont_support_bridges = 1
; duplicate_distance = 6
; elefant_foot_compensation = 0
; end_filament_gcode = "; Filament-specific end gcode"
; end_gcode = G4 ; wait\nM221 S100\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n{if layer_z < max_print_height}G1 Z{z_offset+min(layer_z+30, max_print_height)}{endif} ; Move print head up\nG1 X0 Y200 F3000 ; home X axis\nM84 ; disable motors
; ensure_vertical_shell_thickness = 1
; external_perimeter_extrusion_width = 0.45
; external_perimeter_speed = 20
; external_perimeters_first = 0
; extra_loading_move = -2
; extra_perimeters = 0
; extruder_clearance_height = 20
; extruder_clearance_radius = 20
; extruder_colour = #FFFF00
; extruder_offset = 0x0
; extrusion_axis = E
; extrusion_multiplier = 1
; extrusion_width = 0.45
; fan_always_on = 1
; fan_below_layer_time = 100
; filament_colour = #FF3232
; filament_cooling_final_speed = 3.4
; filament_cooling_initial_speed = 2.2
; filament_cooling_moves = 4
; filament_cost = 24.99
; filament_density = 1.24
; filament_diameter = 1.75
; filament_load_time = 0
; filament_loading_speed = 28
; filament_loading_speed_start = 3
; filament_max_volumetric_speed = 15
; filament_minimal_purge_on_wipe_tower = 15
; filament_notes = "Affordable filament for everyday printing in premium quality manufactured in-house by Josef Prusa"
; filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
; filament_settings_id = "Prusament PLA"
; filament_soluble = 0
; filament_toolchange_delay = 0
; filament_type = PLA
; filament_unload_time = 0
; filament_unloading_speed = 90
; filament_unloading_speed_start = 100
; fill_angle = 0
; fill_density = 20%
; fill_pattern = rectilinear
; first_layer_acceleration = 1000
; first_layer_bed_temperature = 60
; first_layer_extrusion_width = 0.42
; first_layer_height = 0.2
; first_layer_speed = 20
; first_layer_temperature = 215
; gap_fill_speed = 30
; gcode_comments = 0
; gcode_flavor = marlin
; gcode_label_objects = 0
; high_current_on_filament_swap = 0
; host_type = octoprint
; infill_acceleration = 1250
; infill_every_layers = 1
; infill_extruder = 1
; infill_extrusion_width = 0.45
; infill_first = 0
; infill_only_where_needed = 0
; infill_overlap = 25%
; infill_speed = 40
; inherits_cummulative = "0.20mm QUALITY MK3";;
; interface_shells = 0
; layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
; layer_height = 0.2
; machine_max_acceleration_e = 5000,5000
; machine_max_acceleration_extruding = 1250,1250
; machine_max_acceleration_retracting = 1250,1250
; machine_max_acceleration_x = 1000,960
; machine_max_acceleration_y = 1000,960
; machine_max_acceleration_z = 1000,1000
; machine_max_feedrate_e = 120,120
; machine_max_feedrate_x = 200,100
; machine_max_feedrate_y = 200,100
; machine_max_feedrate_z = 12,12
; machine_max_jerk_e = 1.5,1.5
; machine_max_jerk_x = 8,8
; machine_max_jerk_y = 8,8
; machine_max_jerk_z = 0.4,0.4
; machine_min_extruding_rate = 0,0
; machine_min_travel_rate = 0,0
; max_fan_speed = 100
; max_layer_height = 0.25
; max_print_height = 210
; max_print_speed = 200
; max_volumetric_speed = 0
; min_fan_speed = 100
; min_layer_height = 0.07
; min_print_speed = 15
; min_skirt_length = 4
; notes = 
; nozzle_diameter = 0.4
; only_retract_when_crossing_perimeters = 0
; ooze_prevention = 0
; output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{print_time}_{printer_model}.gcode
; overhangs = 1
; parking_pos_retraction = 92
; perimeter_acceleration = 800
; perimeter_extruder = 1
; perimeter_extrusion_width = 0.45
; perimeter_speed = 45
; perimeters = 3
; post_process = 
; print_host = 
; print_settings_id = Greg 0.20mm PLA Small Part
; printer_model = MK3
; printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
; printer_settings_id = Original Prusa i3 MK3
; printer_technology = FFF
; printer_variant = 0.4
; printer_vendor = 
; printhost_apikey = 
; printhost_cafile = 
; raft_layers = 0
; remaining_times = 1
; resolution = 0
; retract_before_travel = 1
; retract_before_wipe = 0%
; retract_layer_change = 1
; retract_length = 0.8
; retract_length_toolchange = 4
; retract_lift = 0.6
; retract_lift_above = 0
; retract_lift_below = 209
; retract_restart_extra = 0
; retract_restart_extra_toolchange = 0
; retract_speed = 35
; seam_position = nearest
; serial_port = 
; serial_speed = 250000
; silent_mode = 1
; single_extruder_multi_material = 0
; single_extruder_multi_material_priming = 0
; skirt_distance = 2
; skirt_height = 1
; skirts = 1
; slice_closing_radius = 0.049
; slowdown_below_layer_time = 20
; small_perimeter_speed = 20
; solid_infill_below_area = 0
; solid_infill_every_layers = 0
; solid_infill_extruder = 1
; solid_infill_extrusion_width = 0.45
; solid_infill_speed = 40
; spiral_vase = 0
; standby_temperature_delta = -5
; start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}18{else}30{endif} ; Filament gcode"
; start_gcode = M115 U3.8.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0 F1000.0 ; intro line\nG1 X100.0 E12.5 F1000.0 ; intro line\nG92 E0.0\nM221 S{if layer_height<0.075}100{else}95{endif}
; support_material = 0
; support_material_angle = 0
; support_material_auto = 1
; support_material_buildplate_only = 1
; support_material_contact_distance = 0.1
; support_material_enforce_layers = 0
; support_material_extruder = 0
; support_material_extrusion_width = 0.35
; support_material_interface_contact_loops = 0
; support_material_interface_extruder = 0
; support_material_interface_layers = 2
; support_material_interface_spacing = 0.2
; support_material_interface_speed = 100%
; support_material_pattern = rectilinear
; support_material_spacing = 2
; support_material_speed = 30
; support_material_synchronize_layers = 0
; support_material_threshold = 45
; support_material_with_sheath = 0
; support_material_xy_spacing = 50%
; temperature = 215
; thin_walls = 0
; threads = 8
; toolchange_gcode = 
; top_fill_pattern = rectilinear
; top_infill_extrusion_width = 0.4
; top_solid_infill_speed = 20
; top_solid_layers = 4
; travel_speed = 180
; use_firmware_retraction = 0
; use_relative_e_distances = 1
; use_volumetric_e = 0
; variable_layer_height = 1
; wipe = 1
; wipe_into_infill = 0
; wipe_into_objects = 0
; wipe_tower = 1
; wipe_tower_bridging = 10
; wipe_tower_rotation_angle = 0
; wipe_tower_width = 60
; wipe_tower_x = 170
; wipe_tower_y = 125
; wiping_volumes_extruders = 70,70
; wiping_volumes_matrix = 0
; xy_size_compensation = 0
; z_offset = 0